UK Plastic Injection Moulding: The Complete Guide for Product Manufacturers

Answering the questions we're asked most often by engineers and procurement teams evaluating injection moulding.

Assembly and Secondary Operations for Injection Moulded Parts

Is a moulded part ever finished when it leaves the tool? Sometimes. More often it still needs joining, fitting, marking or testing before it can go into a product, and those secondary operations can account for a significant share of the total cost of a project. Planning them at the design stage is far cheaper than adding them afterwards.

Why assembly belongs in the design conversation

Most moulded products are made of more than one component. A two-part housing needs to be joined, a button needs a spring, a lens needs a seal. When each of those steps is carried out by a different supplier, parts move between sites, lead times extend, and a part that doesn’t fit becomes a dispute over whose tolerance was at fault.

Where assembly is planned alongside the moulded part, the joint, the locating features and the tolerances can all be designed to suit the method. That usually means fewer components, less handling and a more repeatable product.

Common secondary operations

The operations required depend on the product, but the following are the most widely used for injection moulded components.

  • Ultrasonic welding. High-frequency vibration generates heat at the interface between two parts and fuses them without screws or adhesive. A small ridge moulded into one part, known as an energy director, concentrates the energy at the joint. It suits sealed housings and works most reliably on amorphous plastics such as ABS and polycarbonate. Read more about ultrasonic welding.
  • Snap fits. Cantilever or annular features moulded into the part engage with a mating feature as the parts are pushed together. No additional components are needed, but the geometry and material have to be designed carefully so the feature flexes without overstraining.
  • Threaded inserts and heat staking. Metal inserts give a plastic part a durable thread. They can be fitted after moulding using heat or ultrasonics, or placed in the tool before the shot so they are moulded in. Heat staking melts a moulded post over a component to hold it in place.
  • Pad printing, screen printing and hot foil. Pad printing transfers ink from an etched plate using a silicone pad, which makes it well suited to curved or textured surfaces. Screen printing suits flatter areas. Hot foil uses heat and pressure to transfer a finish or marking.
  • Fitting other components. Seals, gaskets, springs, fasteners, lenses and electronics can be added by hand or with fixtures, depending on the volume.
  • Inspection, testing and packing. Dimensional checks, functional or leak testing, then counting, bagging or kitting to suit how the parts are used on your line.

Designing for assembly

The principle of design for assembly is to reduce the number of parts and make those that remain easy to fit together. For moulded parts, that translates into a few practical guidelines.

  • Include lead-ins and locating features so that parts align without adjustment.
  • Keep sufficient wall thickness around any boss that will take an insert or a screw.
  • Allow for tolerance build-up across the joint, so mating parts still fit at the extremes.
  • Consider whether two components can be moulded as one, and whether that justifies the extra tool complexity.

The last point can go either way. A single, more complex part can cost more in tooling than two simple parts and an assembly step. The right answer depends on volume, which is why it is worth discussing before the design is final.

The benefit of a single site

Carrying out moulding and assembly in one place removes transit time between suppliers, allows problems to be caught sooner because the assemblers and the moulders work together, and leaves one supplier accountable for the finished result.

Assembly support at Naiad

Naiad supports the finishing steps a moulded component often needs, including assembly and other secondary operations, so the process does not stop at the mould tool. Our design review, tooling and injection moulding are handled by one team, which means assembly requirements can be built in from the start. Where a project needs further design or engineering input, we can bring in support through IDC.

If your product is more than a single moulded part, tell us what the finished item needs to look like when it reaches you. We will advise on the options and what each is likely to mean for cost and lead time. You can request a quote or contact the team directly. For a wider overview of the process, see our guide to UK plastic injection moulding.